Wurfarme | C.V. EDITION by SPIDERBOWS - Raven CARBON - ILF - 30-45 lbs
The limbs of the C.V. Edition are based on a core of bamboo wood, which is covered on the outside with a 1.2 mm thick exposed carbon laminate and does not require any additional glass laminate. On the inside, on the other hand, only highly stable, black laminate is used, with a silky-matt shiny surface.
This special limb construction is similar to that of the top model Condor, but its geometry is slightly "toned down". Nevertheless, it guarantees maximum torsional stiffness, extremely forgiving shooting behaviour and very high speeds.
In order to ensure the quality that one associates and can expect with the name of a world and European champion, all bows are tested, signed and prepared ready to shoot by Christian Vorderegger after production.
C.V. Edition - Developed by the world champion
Two years of hard work have gone into the C.V. Edition, which was developed jointly by SPIDERBOWS and Christian Vorderegger, the World and European Champion in the IFAA. It was not easy to meet all his demands and set goals, but SPIDERBOWS has succeeded in building bows with the C.V. Edition that make no compromises.
Characteristics:
- Draw weight @ 19 inch riser (selectable in 5 lbs steps): 30-45 lbs
- Length: Medium (64 inch @21 inch) or Long (66 inch @21 inch)
- ILF System
- Tips: Fast Flight suitable
Scope of delivery:
1 pair
| Draw Weight: |
21-30 lbs31-40 lbs41-50 lbs |
| Fast-Flight: |
Fast-Flight suitable |
| Screw on or ILF Limbs: |
ILF Limbs |
| Limbs Material: |
CarbonCarbon / Wood |
| Shipping weight: |
0,00 kg
|
| Item weight: |
0,00 kg
|
|
Manufacturer's information: |
Manufacturer's name:
BSW Handels GmbH
Address::
Demminer Strasse 32, 17389 Anklam
Country of origin::
Germany
Website:
https://spiderbows.com/
Contact:
contact@spiderbows.com
Brand:
C.V. EDITION by SPIDERBOWS |
Limb labelling
The limbs of a bow are always labelled with an inscription that not only indicates the draw weight of the limbs, but also the length of the riser or the bow length to which the draw weight refers. This labelling can look like this, for example:
25 lbs @ 19 inches or
19H 25 lbs 62 inches or
25 lbs @ 62 inches or also
62 inches / 25 lbs
If no length of the riser is specified, a 25 inch riser is usually the basis for the draw weight specification. In the case of special bows where the limbs are only suitable for the respective riser, the draw weight is of course based on the corresponding riser.
Many limbs are also available in three different lengths - usually called short, medium and long - with which the bow lengths 66, 68 and 70 inches can be achieved despite the same riser.
Converting the draw weight and bow length
Many limbs have universal mounting options that allow them to be used at least on different risers from one manufacturer or even across manufacturers. However, it is important to note that the use of a shorter or longer riser will result in a change in bow length and draw weight.
As a rule of thumb, you can remember the following:
-2 inch riser length = -2 inch bow length & +2 lbs draw weight
or
+2 inch riser length = +2 inch bow length & -2 lbs draw weight
I.e.: If the riser is 2 inches shorter than the length to which the draw weight specification on the limbs refers, the bow is 2 inches shorter and the specified draw weight increases by 2 lbs.
Example table for limbs with the draw weight specification for a 25 inch riser (e.g. 20 lbs @ 25 inches) and a bow length of 68 inches. The table is incomplete and can be continued as required depending on the centre section length.
